GE Monogram Refrigerator ZDBI240 User Manual

Design Guide with  
Installation  
Instructions  
Wine Chiller, Wine Reserve  
and Beverage Center  
monogram.com  
 
Design Guide  
THE INSTALLATION SPACE (cont.)  
THE INSTALLATION SPACE  
Flush  
Installation  
Dim. A  
Filler panel or cleat  
to be set back even  
with front of case.  
CABINET  
CABINET  
Front edge of product case  
Front face  
110°  
120°  
These products will fit flush to  
adjacent cabinets when installed  
with a Dim. A-width filler panel  
or cleat. The filler panel should  
be recessed or set back behind  
the door and even with the front  
edge of the product case.  
NOTE:  
Handle and handle  
standoff depth is 1-3/4"  
Product  
Dim. A  
ZDWI240, ZDBI240  
ZDWC240, ZDWR240  
ZDBC240, ZDBR240  
1"  
*For a standard installation of Custom-Framed unit: The  
product must be installed so that the front face will project 2"  
forward of adjacent cabinets. This position will allow a full door  
swing and prevent interference with adjacent cabinetry. The  
opening between cabinets must be 23-3/4" minimum.  
1/2"  
1/2"  
*For a standard installation of Stainless Steel unit: The product  
must be installed so that the front face will project 1-3/4"  
forward of adjacent cabinets. This position will allow a full door  
swing and prevent interference with adjacent cabinetry. The  
opening between cabinets must be 23-3/4" minimum.  
Standard  
Installation  
**For a flush installation of Stainless Steel unit: Install a  
1/2"-wide filler strip on the hinge side. The filler strip will act as  
a spacer between the door case and adjacent cabinets and will  
prevent interference with the cabinet door swing. Recess the  
filler strip 2" back from the front face of the unit, or even with  
the front edge of the product case (behind the gasket). The width  
of the opening must be 24-1/4" (including the 1/2" filler strip).  
***For a flush installation of Custom-Framed unit: Install a  
1"-wide filler strip on the hinge side. The filler strip will act as  
a spacer between the door case and adjacent cabinets and  
will prevent interference with the cabinet door swing. Recess  
the filler strip 2" back from the front face of the unit, or even with  
the front edge of the product case (behind the gasket). The width  
of the opening must be 24-3/4" (including the 1" filler strip).  
CABINET  
CABINET  
Front edge of product case  
Front face  
Dim. A  
110°  
120°  
In a standard installation,  
the product will project forward  
of adjacent cabinets. See Dim. A.  
Product  
Dim. A  
2"  
ZDWI240, ZDBI240  
ZDWC240, ZDWR240  
ZDBC240, ZDBR240  
1-3/4"  
1-3/4"  
• The wine chiller, wine reserve and beverage center can  
be installed freestanding.  
Additional Specifications  
A 120 volt 60Hz., 15 or 20 amp power supply is required.  
An individual properly grounded branch circuit or circuit  
breaker is recommended. Install a properly grounded  
3-prong electrical receptacle recessed into the back wall  
as shown. Electrical must be located on rear wall as shown.  
NOTE: GFI (ground fault interrupter) is not recommended.  
3
 
Design Guide  
PRODUCT CLEARANCES  
SIDE-BY-SIDE INSTALLATIONS  
Increase storage capacity by installing two Monogram  
beverage centers, wine chillers or wine reserves together.  
Or, for a complete refreshment center, install any two  
of these units together.  
The stainless steel wine chiller, wine reserve and  
beverage center is factory set for a 110° door swing.  
Models that accept custom panels have a 95° door  
swing.  
When installed in a corner:  
• A side-by-side installation requires at least a 47-1/2"-  
wide minimum opening for standard installation and  
a 48-1/2"-wide minimum opening for flush installation  
of stainless steel models. A 49-1/2"-wide minimum  
opening is required for side-by-side flush installation  
of custom framed models.  
Allow 4" min. clearance on the hinge side for the 90°  
door swing and to allow racks to slide out.  
• Allow 10" minimum clearance on the hinge side for  
a full 110° door swing. (Models ZDWI240WII and  
ZDBI240WII have a 95° door swing.)  
NOTE: Custom handle clearances may vary, depending  
on custom handle depth.  
• Products must operate from separate, properly  
grounded receptacles.  
10" Minimum  
to Wall  
90° Door Swing  
21-5/8"  
23-5/8"  
90ϒ  
110°*  
*95° Door Swing on Custom Frame Models  
4" Minimum  
to Wall  
• The door swing is reversible on all models. If desired,  
change the door swing before installation or before  
installing the custom frame panel.  
Choose the location:  
• These products may be closed in on the top and  
three sides as long as the front is unobstructed for air  
circulation and proper access to the door.  
• Do not install these products where the temperature  
will go below 55°F (13°C) or above 90°F (32°C).  
• Do not install where it will be subject to direct sunlight,  
heat or moisture.  
• These products are not designed to be stacked one  
over the other.  
Black or Stainless Steel Toekick Options  
• These products are shipped with a black toekick  
installed. An optional stainless steel toekick is also  
supplied with each product. For shipping purposes, the  
stainless steel toekick is secured to the back of the unit.  
4
 
Installation Instructions  
TOOLS REQUIRED  
• #2 Phillips screwdriver  
• Adjustable wrench  
STAINING WOOD DRAWER FRONTS  
The drawer fronts are unfinished cherry wood. During  
use, oil from hands may accumulate and stain the  
wood.  
• The drawer fronts may be stained and sealed to  
match adjacent cabinetry. The tinted glass will make  
the stained wood appear darker. A true color match  
can be seen only when the door is opened.  
• Apply the stain and sealer according to the  
manufacturer’s instructions. To avoid unpleasant  
odor, keep the door open to ventilate and allow  
the stain/sealer to dry completely before using  
the product.  
PARTS SUPPLIED  
• Monogram nameplate  
• Hardware for changing door swing  
• Optional stainless steel toekick with screws and  
spacers  
• Left and right side hinge covers  
• Top screw hole cover  
GROUNDING THE WINE CHILLER,  
WINE RESERVE AND BEVERAGE  
CENTER  
INSTALLING THE CUSTOM FRAME PANEL  
Go to page 6 for custom frame panel size, depending  
on your cabinet size and style.  
IMPORTANT –  
FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE  
PROPERLY GROUNDED.  
Please read carefully.  
• Install a custom handle of your choice onto the  
custom panel before the panel is secured to the door.  
• The custom panel should be installed before sliding  
the product into the installation location.  
The power cord of this appliance is equipped with  
a three-prong (grounding) plug which mates with a  
standard three-prong (grounding) wall receptacle to  
minimize the possibility of electric shock hazard from  
this appliance.  
STEP 1 REMOVE PACKAGING  
• Remove corner blocks and foam drawer stops.  
• Remove all packing material, tape and protective  
plastic coverings.  
• Remove stainless steel toekick taped to the back  
of the unit.  
Have the wall outlet and circuit checked by a qualified  
electrician to make sure the outlet is properly grounded.  
Where a standard 2-prong wall outlet is encountered, it  
is your personal responsibility and obligation to have it  
replaced with a properly grounded 3-prong wall outlet.  
CAUTION:  
Small objects are a choke  
hazard for children. Remove and discard any parts  
not used.  
DO NOT, UNDER ANY  
CIRCUMSTANCES, CUT  
OR REMOVE THE THIRD  
(GROUND) PRONG  
MISE EN GARDE :  
Les petits  
objets peuvent étrangler les enfants. Il faut jeter toutes  
les piéces qui ne sont pas utilisées.  
FROM THE POWER CORD.  
DO NOT USE AN ADAPTER PLUG TO CONNECT THE  
REFRIGERATOR TO A 2-PRONG OUTLET.  
DO NOT USE AN EXTENSION CORD WITH THIS  
APPLIANCE.  
5
 
Installation Instructions  
STEP 2 REVERSE DOOR SWING  
SKIP THIS STEP IF DOOR SWING SUITS THE  
INSTALLATION  
Install  
3 Hinge  
Screws  
Parts Included:  
• Top left case hinge  
Remove  
Top Hinge  
• Bottom left case hinge  
• Left and right side decorative hinge cover  
• Decorative hinge screw hole cover  
• Torx® driver bit  
Hinge  
Pin and  
Bracket  
Tools Required:  
• Phillips screwdriver  
• Electric drill  
Door Stop  
and Cam Riser  
Remove the door:  
• Flatten the shipping carton to use as a pad.  
• Remove the 2 screws and the toekick. Set aside  
the screws and toekick for final installation.  
• Use the supplied Torx® bit and electric drill to remove  
the 3 screws holding the top case hinge. Lift off the  
hinge. (Screws will be used to install the new hinge.)  
• Lift the door off the bottom case hinge.  
Remove  
Hinge  
• Remove the bottom case hinge pin and bracket.  
Apply Monogram Nameplate:  
• Install the Monogram nameplate. See instructions  
and template on back cover.  
Rotate the door:  
The handle will be on the right side of the door; hinges  
will be installed on the left side of the case.  
• Remove the door stop and cam riser on the original  
bottom right side of the door.  
Install Toekick  
The toekick has a  
cutout on the left  
and right sides.  
• Remove the fill plug on the top right side  
of the door.  
Remove  
the plug  
• Turn the door over and reinstall the fill plug on  
the new left side.  
on the left  
side and  
reinstall  
on the right  
Reinstall the door:  
• Install the original door stop and cam riser onto  
the bottom left side of the door.  
side. If you  
choose to  
• Install the new supplied bottom case hinge pin and  
bracket onto bottom left side.  
install the  
stainless steel toekick,  
• Place the door onto the bottom case hinge.  
• Install the supplied left-hand top case hinge with  
the 3 original screws.  
• Select the hinge cover marked with an “L”.  
• Peel backing off the tape inside the decorative hinge  
reinstall the plug on the right side of that toekick.  
• Install original screws and spacers or screws and  
spacers supplied with the stainless steel toekick.  
Install screws through the spacer standoff, toekick  
and into the base as shown.  
cover.  
Install Covers  
• Press and snap the hinge  
cover into place.  
• Snap the screw hole cover into  
place on the opposite side.  
IMPORTANT:  
Check to be sure screws are tight and that the door  
is straight and does not sag. The door should swing  
freely.  
6
 
Installation Instructions  
CUSTOM FRAME PANEL MODELS  
STEP 3 LEVEL  
Model ZDWI240WII and ZDBI240WII  
• Use an adjustable wrench to turn the leveling legs and  
raise or lower the product.  
These models require a custom panel frame surrounding  
the glass. There are two options: the panel may be 29-3/4"  
or 30" high. A 30" panel requires a notch cut into the bottom  
of the panel to avoid interference with the hinges.  
• Rout the back side of the panel to the dimensions shown.  
• A custom handle of your choice must be installed before  
the panel is mounted onto the door.  
• Adjust carefully; the product should be level and plumb  
with cabinetry, and should align with adjacent toekick  
height.  
Turn Right to Lower  
Turn Left to Raise  
NOTE: The 4 corners  
of the routed areas  
must be squared  
to fit the corners  
of the metal  
door frame.  
Option 1  
Option 2  
23-1/8”  
23-1/8”  
2-1/4”  
2-1/4”  
wide,  
If you skipped Step 2:  
• Select the hinge cover marked “R” or “L”, depending  
on door swing.  
• Peel backing off the tape inside the decorative  
hinge cover. Press and snap into position.  
• Snap the screw hole cover into place on the  
opposite side.  
all sides  
25-1/4”  
25-1/4”  
Rout the back  
side of the  
opening 7/16”  
deep, 1-1/8” wide  
Rout the  
back side  
of the  
opening  
7/16”deep,  
1-1/8” wide  
GLASS  
18-5/8”  
30”  
29-3/4”  
GLASS  
18-5/8”  
2-1/2” at  
bottom  
3/4” Thick Custom Panel,  
Back Side  
2-1/4”  
2-1/4”  
1/8”  
1/4”  
Cut the notch  
1/8” deep, 1/4”  
wide and 1/4”  
high  
NOTE: Right-hand models  
illustrated. Cut notches  
for hinge clearance on the  
opposite side for left-hand  
door swing.  
STEP 4 CONNECT POWER  
• Connect power cord plug to a properly grounded  
receptacle.  
1/4”  
• Check to make sure power is on by opening the door  
to see if interior light turns on.  
Choose Option 1 or Option 2 panel size depending on cabinetry  
size or style.  
NOTE: A solid panel that covers the door glass CANNOT be  
installed on these models.  
STEP 5 SLIDE PRODUCT INTO  
Install the custom panel:  
• Open the door fully.  
• Remove the gasket surrounding the inside of the door to  
expose the existing screw holes for the custom panel.  
• Hold the custom frame panel against the door and align  
carefully, top to bottom and side to side. Mark screw hole  
locations on the back side of the panel.  
THE CUTOUT  
Carefully, slide the unit into the opening. Be careful  
not to entangle the power cord.  
Make certain that the door protrudes 1" beyond  
the surrounding cabinets (1-7/8" for custom frame  
models).  
• Check again to be sure the unit is level.  
• Drill pilot holes in the back side of the custom panel. In  
hardwood, drill 3/32" pilot holes. In softwood, drill 5/64" holes.  
• Secure the prepared panel to the door using ten (10)  
#8 x 5/8" screws. Drive the screws through the door frame  
and into the wood.  
STEP 6 INSTALL NAMEPLATE  
• Follow instructions on the back page for installation of  
the Monogram nameplate.  
• Replace the gasket.  
#8 x 5/8"  
Screws  
GLASS  
Back  
Door  
Frame  
STEP 7 SET TEMPERATURE CONTROLS  
• The temperature controls are preset. Refer to the  
Owner’s Manual for more information. Allow 24 hours  
for temperature to stabilize.  
Custom  
Framed  
Panel  
7
 
TEMPLATE FOR NAMEPLATE LOCATION  
To position nameplate:  
• Cut template along dotted line.  
• Hold or tape template behind glass  
door so that it is visible from the  
front side.  
• Remove backing from nameplate.  
• Place nameplate onto front side of  
door, matching illustration on the  
template.  
IMPORTANT: Nameplate must  
be placed on the opposite side  
of the door handle.  
Note: While performing installations described in this book,  
safety glasses or goggles should be worn.  
For Monogram® local service in your area, call  
1.800.444.1845.  
Note: Product improvement is a continuing endeavor at  
General Electric. Therefore, materials, appearance and  
specifications are subject to change without notice.  
Pub. No. 31-46122-3  
Part No. 197D7840P001  
09-09 JR  
Printed in Slovenia  
 

Contec Personal Computer SEH 9450 LAS User Manual
Craftsman Lawn Mower 37416 User Manual
Crate Amplifiers Stereo Amplifier BT220 User Manual
Cuisinart Coffeemaker DCC 2900 User Manual
Delfield Refrigerator UCD4464N 12 User Manual
Digicom Network Card 8D5449 User Manual
Electro Voice Musical Instrument Amplifier GS 2000A User Manual
First Alert Home Security System fa11oc User Manual
Fisher Price Satellite Radio N9326 User Manual
Gigabyte Server AP64D User Manual