Installation and Operating Instructions
INDUKCVPRG Issue 2
Dimplex Dual Warmth Heater
Model(s): CVP1 & CVP1T
Dimensions
(millimetres)
Fig. 1
shelf
Models
Specification
CVP1
1000W Thermostat / 2 Neon Heat
Switches
CVP1T
1000W Thermostat / 2 Neon Heat
Switches & 24 Hour Timer
CVP1T shown
floor
wall
mounted
mounted
THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
DO NOT connect the Brown (Live) or the Blue (Neutral) wires to the
Earth terminal of your 13 amp plug. If the terminals of the plug are
unmarked or you are in any doubt, consult a qualified electrician.
CAUTION: If you use this heater in conjunction with a thermal control,
programme controller, timer or any other device which switches the
heater on automatically observe all safety warnings at all times.
IMPORTANT SAFETYADVICE
WARNING - THIS APPLIANCE MUST NOT BE USED IN A
BATHROOM
WARNING – DO NOT USE THIS HEATER IN THE IMMEDIATE
SURROUNDINGS OF A BATH, A SHOWER OR A SWIMMING
POOL
Positioning the Heater
Select the position for the heater ensuring there is clearance from any
furniture and fittings of at least 150mm above the heater, 230mm below
(wall mounted) and 75mm each side - see Fig. 1. Curtains must not be
closer than 150mm from the top of the heater. If used in a free-standing
position the heater should be on a flat stable surface.
WARNING – THIS HEATER MUST NOT BE LOCATED
IMMEDIATELY BELOW A FIXED SOCKET OUTLET.
DO NOT USE THE HEATER UNTIL THE FEET OR WALL
BRACKETS ARE FITTED CORRECTLY.
FOLLOW these instructions carefully.
Free Standing Operation
NEVER USE THE HEATER FREE STANDING WITHOUT THE FEET
FITTED.
The heater carries a warning ‘DO NOT COVER’ to alert the user
to the risk of fire that exists if the heater is accidentally covered.
This appliance is not intended for use by children or other
persons without assistance or supervision if their physical,
sensory or mental capabilities prevent them from using it safely.
Children should be supervised to ensure that they do not play
with the appliance.
1.
2.
Lay the heater on it’s front.
Locate and remove the two foot fixing screws using a X-head
screwdriver.
3.
4.
Place the feet over the base of the heater, align holes and
engage hook on foot into recess on the back of the heater - see
Fig. 2.
We recommend a guard be fitted to ensure contact with the
heater is avoided and objects cannot be inserted in to the
product.
Replace the screws but do not over tighten.
If the mains lead is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified person
in order to avoid a hazard.
recess
For further information, please contact our guard supplier direct
on Tel. No. 01603 667957, or in case of difficulty or for further
advice contact the Customer Helpline - (details on back page)
Electrical
WARNING – THIS APPLIANCE MUST BE EARTHED
If the socket outlets in your home are not of the 13 amp BS1363 type
they will not accept the plug connected to this heater,
therefore cut off the plug. When cut off this plug can constitute a shock
hazard if inserted into a socket outlet. It must therefore be disposed of
safely.
hook
Fig. 2
Before wiring the appropriate plug please note that the wires in this
mains lead are coloured in accordance with the following code:
GREEN/YELLOW - EARTH
BLUE - NEUTRAL
BROWN - LIVE
Connect the Green/Yellow wire to the terminal marked E or the earth
symbol or coloured Green or Green/Yellow.
Connect the Brown wire to the terminal marked L or coloured Red.
Connect the Blue wire to the terminal marked N or coloured Black.
Installation
Three identical wall mounting brackets are stored in the
polystyrene packaging of the heater. Please note that the
radiator must only be wall mounted using the brackets
supplied.
Warning: This heater must not be located immediately below a fixed
socket outlet. The plug must be accessible after heater installation.
when the ‘ADVANCE’ programme is running the ‘ADVANCE’ feature
will be automatically cancelled and the programme will run as normal.
Note - Timer Memory Back Up Batteries - Once the heater has been
left plugged in with the socket switched on for at least 72 hours the
timer’s memory back up batteries will be fully charged.
ON
13 : 17
P1
Once the timer batteries are fully charged, if there is a power cut or if
the heater is disconnected from the mains for less than six months,
then the timer will continue to keep time & the settings in the memory
will remain intact.
OFF
ADVANCE
ON OFF
AUTO
MAN
If however the timer back up batteries have not been charged fully, or
if the heater is deprived of power for longer than six months, then the
time and the programme settings are likely to be lost and you may
therefore need to reset the time and the programme before using the
AUTO MODE again.
Fig. 5
Safety Overheat Protection
The heater is fitted with a thermal safety cut-out which will switch off the
heater should it overheat for any reason. If the cut-out
operates it is the result of abnormal overheating, and the Customer
Services Helpline should be contacted for further advice.
Digital Timer Operation (CVP1T model only)
IMPORTANT: Remember to observe all safety warnings when operating
the heater on auto setting, either attended or unattended.
The timer allows you to select ‘AUTO’, ‘MAN ON’ or ’MAN OFF’ by
pressing the ‘MODE’ button until the required MODE appears at the
bottom of the timer display.
‘AUTO’ MODE allows the heater to switch ON and OFF according to a
set 24 Hour program period (see ‘Setting Programs’ section below).
‘MAN ON’ MODE allows power to the heater uninterrupted by the
program settings.
‘MAN OFF’ MODE switches off all heater operation completely.
Key Lock:
If ‘ENTER’ and ‘MODE’ are pressed within 1 second, the keys will be
locked. The user will know the keys are locked as the lock symbol ‘
’
will be displayed on the top left hand corner of the screen. To unlock the
keypad, press ‘ENTER’ and then ‘MODE’ within 1 second.
Initial Operation
For initial use, plug the heater into a regular household power point and
turn the power on. The timer is now ready to be set up for use.
Setting Current Time
1. Press the ‘PROGRAM’ button ONCE. The clock symbol
appears
on the top left hand side of the screen. The user can now set the clock.
2. The hour digit will flash. To adjust the hour use the ‘-‘ & ‘+’ buttons.
Confirm the hour digit by pressing ‘ENTER’.
3. Once ‘ENTER’ has been pressed the minutes will flash. To adjust the
minutes use the ‘-‘&‘+’ buttons. Confirm the minute digit by pressing
‘ENTER’.
4. The timer now returns to the default display.
5. To reset incorrect time, repeat previous steps.
Once the correct time is set, a total of four ON/OFF time programs can
be set for operation. There are two program options.
Setting Programmes
Press the ‘PROGRAM’ key twice to set the programs.
You are now setting the programs starting with P1 ‘ON’.
SETTING P1 ON TIME:
1. To set the hour use the ‘-‘ & ‘+’ buttons. Confirm the hour digit by
pressing ‘ENTER’.
2. To set the minutes use the ‘-‘ & ‘+’ buttons. Confirm the minute digit
by pressing ‘ENTER’.
Note: The minutes can only be set in 10 minute blocks in programme
‘MODE’.
SETTING P1 OFF TIME:
3. To set the hour use the ‘-‘ & ‘+’ buttons. Confirm the hour digit by
pressing ‘ENTER’.
4. To set the minutes use the ‘-‘ & ‘+’ buttons. Confirm the minute digit
by pressing ‘ENTER’.
Repeat steps 1 to 4 to programme P2, P3 & P4. After programming P4
‘OFF’ you automatically exit to the default display.
At any time while programming the timer you can press the ‘PROGRAM’
button to exit to the default display.
The Advance Function
When in ‘AUTO’ MODE, if the ‘+’ button is pressed for longer than 2
seconds the programme will ADVANCE to the next setting programmed
and will only revert back to the program when the subsequent programme
time is reached. When the ‘ADVANCE’function is running the ‘ADVANCE’
segment will be displayed on the LCD screen. If the ‘-‘ button is pressed
Cleaning
WARNING -ALWAYS DISCONNECT THE POWER SUPPLY BEFORE
CLEANING THE HEATER.
Do not use detergents, abrasive cleaning powder or polish of any kind
on the body of the heater.
Allow the heater to cool, then wipe with a dry cloth to remove dust and
a damp cloth (not wet) to clean off stains. Be careful not to allow
moisture in to the heater.
After Sales Service
Your product is guaranteed for three years from the date of
purchase.
Within this period, we undertake to repair or exchange this
product free of charge provided it has been installed and
operated in accordance with these instructions.
Your rights under this guarantee are additional to your statutory rights,
which in turn are not affected by this guarantee.
Should you require after sales service you should contact our customer
services help desk on 0870 727 0101. It would assist us if you can
quote the model number, series, date of purchase, and nature of the
fault at the time of your call.
Please do not return a faulty product to us in the first instance as this
may result in loss or damage and delay in providing you with a
satisfactory service.
The inner panel of this heater is filled with a precise quantity of special
oil. Repairs requiring opening of the oil container are only to be made by
the manufacturer or its service agent. For further advice if an oil leak is
suspected please contact our Customer Services Helpline. Regulations
concerning the disposal of oil when scrapping the appliance must be
followed.
Please retain your receipt as proof of purchase.
The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility
(EMC) EN55014, EN60555-2 and EN60555-3 which cover the essential requirements of EEC Directives 73/23 and 89/336
Glen Dimplex UK Limited
Millbrook House
Grange Drive
Hedge End
Southampton
UK customer help line (8.00AM – 6.00PM Mon-Fri; 8.30AM-1.00PM Sat)
Customer Services:
Tel.
0870 7270101
Fax.
e-mail
Tel.
0870 7270102
01 8424833
Republic of Ireland
Hampshire. SO30 2DF
[c] Glen Dimplex UK Limited
All rights reserved. Material contained in this publication may not be reproduced in whole or in part, without prior permission in writing of Glen Dimplex UK Limited.
|